Directed Electronics 700 Installation Guide

© 2003 Directed Electronics, Inc. Vista, CA N700J 12-03Model 700JInstallation Guide®

10 © 2003 Directed Electronics, Inc. Vista, CAmaking your connectionsWhen connecting the security system’s wires to the vehicle wires it is important

© 2003 Directed Electronics, Inc. Vista, CA 111. Using your wire strippers and razor knife, strip approximately 1/2-inch of insulation off the wire to

12 © 2003 Directed Electronics, Inc. Vista, CAprimary harness (H1) wire connection guideThis section of the installation guide describes in detail the

© 2003 Directed Electronics, Inc. Vista, CA 13H1/2 WHITE (-/+) SELECTABLE LIGHT FLASH OUTPUTAs shipped, with the light flash polarity jumper inside th

14 © 2003 Directed Electronics, Inc. Vista, CAIMPORTANT! Never use this wire to drive anything except a relay or a low-current input! This tran-sistor

© 2003 Directed Electronics, Inc. Vista, CA 15H1/8 BLACK (-) CHASSIS GROUND CONNECTIONRemove any paint and connect this wire to bare metal, preferably

16 © 2003 Directed Electronics, Inc. Vista, CAH1/11 RED (+) 12V CONSTANT POWER INPUTBefore connecting this wire, remove the supplied fuse. Connect to

© 2003 Directed Electronics, Inc. Vista, CA 17optional sensor harness, 4-pin connectorThe four-pin shock sensor harness is optional and is not include

18 © 2003 Directed Electronics, Inc. Vista, CAdetect both vehicle intrusions and faulty zones. For vehicles that do not have a trunk pin, or if the pi

© 2003 Directed Electronics, Inc. Vista, CA 19means of disarming the databus interface module is through the OEM transmitter or coded Valet switch. (R

2 © 2003 Directed Electronics, Inc. Vista, CAWhat Is Included . . . . . . . . . . . . . . . . . . . . . . 3Product Description . . . . . . . . . . . .

20 © 2003 Directed Electronics, Inc. Vista, CAdriving factory parking light relays. In the (+) position, the on-board relay is enabled and will supply

© 2003 Directed Electronics, Inc. Vista, CA 21NOTE: When adjusting the sensor, it must be mounted in the same location where it will be after the inst

22 © 2003 Directed Electronics, Inc. Vista, CA4. Program the feature: While HOLDING the Valet/program switch, you can toggle the featureon and off usi

© 2003 Directed Electronics, Inc. Vista, CA 23TO EXIT THE LEARN ROUTINE, DO ONE OF THE FOLLOWING: Close the open door. Turn the ignition on. No ac

24 © 2003 Directed Electronics, Inc. Vista, CAaccessory circuit in the vehicle to keep the radio and other accessories on after the ignition is turned

© 2003 Directed Electronics, Inc. Vista, CA 25troubleshooting Optional starter kill does not work:Is the correct starter wire being interrupted? If t

26 © 2003 Directed Electronics, Inc. Vista, CA

© 2003 Directed Electronics, Inc. Vista, CA 3what is included The control module (see diagram) A Revenger®Soft Chirp®siren The plug-in Valet®/progr

4 © 2003 Directed Electronics, Inc. Vista, CAproduct descriptionThis unit is used to enhance a vehicle’s original equipment from manufacturer (OEM) fa

© 2003 Directed Electronics, Inc. Vista, CA 5AFTER THE INSTALLATION Test all functions. The “Using Your System” section of the Owner’s Guide is very

6 © 2003 Directed Electronics, Inc. Vista, CA Point the siren down so water does not collect in it. Never put the control module in the engine compa

© 2003 Directed Electronics, Inc. Vista, CA 7This system has Remote Valet, so the user can enter and exit Valet Mode without having to reach theValet/

8 © 2003 Directed Electronics, Inc. Vista, CAIf the optional Failsafe®Starter Kill Relay (not included with this unit) or its connections are immediat

© 2003 Directed Electronics, Inc. Vista, CA 9How to find (+)12V ignition with your multimeter:1. Set to DCV or DC voltage (12V or 20V is fine).2. Atta