Directed Electronics 50.7X Specifications download pdf

SPECIFICATIONS

ELECTRICAL

CURRENT CONSUMPTION

VOLTAGE REQUIREMENTS

ALARM CONTACTS

TAMPER CONTACTS

ACOUSTIC SENSOR

PHYSICAL

SIZE

WEIGHT

GLASS

TYPES

SIZES

87 x 50.7 x 28.6 mm (3.4 x 2.0 x 1.1 in.)

63.70g (2.25

OZ.)

Intended to be connected to a UL control panel capable of providing 4

hours of standby power. Test annually.

Specifications are subject to change without prior notice. Should

any questions arise please contact your nearest distributor.

ROKONET LIMITED WARRANTY

Rokonet Electronics, Ltd. and its subsidiaries and affiliates ("Seller")

warrants its products to be free from defects in materials and workmanship

under normal use for 18 months from the date of production. Because

Seller does not install or connect the product and because the product may

be used in conjunction with products not manufactured by Seller, Seller

cannot guarantee the performance of the security system which uses this

product. Seller's obligation and liability under this warranty is expressly

limited to repairing or replacing, at Seller's option, within a reasonable time

after the date of delivery, any product not meeting the specifications.

Seller makes no other warranty, expressed or implied, and makes no

warranty of merchantability or of fitness for any particular purpose.

In no case shall seller be liable for any consequential of incidental damages

for breach of this or any other warranty, expressed or implied, or upon any

other basis of liability whatsoever.

Seller's obligation under this warranty shall not include any transportation

charges or costs of installation or any liability for direct, indirect, or

consequential damages or delay.

Seller does not represent that its products may not be compromised or

circumvented; that the product will prevent any personal injury or property

loss by burglary, robbery, fire or otherwise; or that the product will in all

cases provide adequate warning or protection. Buyer understands that a

properly installed and maintained alarm may only reduce the risk of burglary,

robbery of fire without warning, but it is not insurance or a guarantee that

such will not occur or that there will be no personal injury or property loss

as a result.

Consequently seller shall have no liability for any personal injury, property

damage or other loss based on a claim that the product fails to give

warning. However, if seller is held liable, whether directly or indirectly, for

any loss or damage arising under this limited warranty or otherwise,

regardless of cause of origin, seller's maximum liability shall not in any

case exceed the purchase price of the product, which shall be the complete

and exclusive remedy against seller.

No employee or representative of Seller is authorized to change this

warranty in any way or grant any other warranty.

WARNING: This product should be tested at least once a week.

ROKONET ELECTRONICS LTD.

14 HACHOMA ST.

75655 RISHON LETZION. ISRAEL.

TEL: (972) 3 961 6555 FAX: (972) 3 961 6584

TEL: (1) 800 344 2025

TEL: (44) 1527 576 765

TEL: (33) 1 4367 0077

TEL: (49) 821 742 660

TEL: (39) 35 683013

5 INS 60 B

ROKONET USA:

ROKONET UK:

ROKONET FRANCE:

ROKONET GERMANY:

ROKONET ITALY:

FAX: (1) 914 592 1271

FAX: (44) 1527 576 816

FAX: (33) 1 4367 0099

FAX: (49) 821 742 499

FAX: (39) 35 683013

20mA at 12V (24mA max)

9.3 - 16 VDC

NC, 24 VDC, 50mA

NC, 24 VDC, 0.5A

Omni Directional Microphone

Plate, laminated, wired & tempered.

30 x 30cm (12" x 12") minimum, except

for 9m / 30ft RG-61 with 50 x 50cm

(20" x 20")

0˚C to 55˚C (32˚F to 131˚F)

-20˚C to 60˚C (-4˚F to 140˚F)

ENVIRONMENTAL

OPERATING TEMPERATURE

STORAGE TEMPERATURE

RG-61U

Rev.B

FOR MORE INFORMATION SEE TIN-2

There are three types of indication in normal mode:

Active Supervision: Any loud sounds such as clapping, whistling or key-

jingling should produce a flash of the VITRON's LED.

This verifies that the VITRON is active. The alarm

relay is not opened.

Passive Supervision: The Vitron continuously monitors its audio channel.

If no sounds are registered for more than 24 hours

the LED will flash rapidly. This indication will

persist until a sound is registered. The alarm relay

is not opened.

Alarm: On detection of framed glass being broken from

outside the LED will light continuously for 3 seconds

and the alarm relay will open.

STEP 7 NORMAL OPERATION

Note: all tests should be conducted under worst-case conditions. All

sounds should be generated behind curtains or blinds.

Observe the VITRON and note any disturbances:

STEP 6 MEMORY INDICATION

To use the MEMORY option - remove the Jumper. The LED is

latched on the first alarm.

The LED is reset by temporarily removing the power from the detector

(using a Switched 12V line from the control panel).

MEM

OFF

Wire the cable to the Terminal Block as follows (see fig 5):

12 VDC

ALARM

TAMPER

EOL

: Power supply inputs

: Normally-Closed relay outputs

: Normally-Closed Tamper switch outputs

: End-of-Line resistor connection

STEP 4 TERMINAL WIRING

NOTE: The VITRON will return to NORMAL mode after two minutes.

Setting the "CODE" switch and pressing the "Manual" button at any

time will initiate another two minutes of Full Remote Test Mode.

LED Indication

Blinks once every 2 sec.

Rapid Flashes

Continuously ON for 3 sec.

Disturbance Possible Cause

NONE

YES

* * *

Low frequency sound

High frequency sound

Fig 5: VITRON PCB - General View

Testing should be performed using the RG65 VITRON tester which has

been specially designed and calibrated to give accurate range test results.

Set lower selector switch on RG65 to CODE setting. Press operating button

on tester to put unit into test mode. VITRON LED will blink every 2 seconds.

HIGH FREQUENCY (AUDIO) TEST:

Position the Glass Break Simulator at the farthest point on the protected

glass and face it into the room. Set lower selector to GLASS setting and

upper to type of glass to be simulated. Generate glass-break sound by

pressing operating button. Verify that VITRON LED comes on for 3 seconds

and ALARM relay is activated.

LOW FREQUENCY TEST:

Tap the window gently. (Caution: breaking glass may cause injury).

Verify that the VITRON produces several rapid flashes of its LED in

conjunction with each tap. The ALARM relay is not activated in this case.

STEP 5 TESTING

ENVIRONMENTAL TEST

Operate all devices in the protected region that may interfere with the

detector, including air conditioners, fans, radios etc.

If disturbances occur, re - position the unit and re-test.

Turn all noise generating equipment off and wait until unit returns to

NORMAL mode.

If RG65 tester is not available test mode can be initiated by opening front

cover and pressing the test button. The VITRON LED will blink every 2

seconds. Replace front cover. VITRON will automatically return to normal

operation after 5 minutes. Pressing the button again during the test mode will

immediately return unit to normal mode. Functional test can now be performed

using another tester.

NOTE: Any test performed using testers other than RG65 will not give

accurate range results.

6/98

RG-60 & RG-61 models for up to 4.5m or 9m ranges

Suitable for most common types of plate, tempered, laminated and wired

glass:

Minimum size for all types of glass: 30cm x 30cm (12'' x 12'')

Thickness: Plate 3.2 mm - 6.4mm (1/8'' - 1/4'')

Tempered,

Laminated, 6.4 mm (1/4'')

Wired

GENERAL DESCRIPTION

The VITRON is an advanced microprocessor based Acoustic Glass Break

detector. Using advanced glass-breaking pattern analysis of both low

frequency "flex" & high frequency "shatter" channels it will detect the

breaking of most common types of framed glass panes while ignoring false

Table 1: VITRON range of coverage

3.2 - 6.4mm

(1/8''-1/4'')

Thickness

Angle (degrees)

Percent of max range

100

MAIN FEATURES

VITRON range of coverage depends on (a) the type of glass (see Table 1)

(b) the angle between VITRON and glass (see Fig 1)

STEP 1 RANGE OF COVERAGE

INSTALLATION PROCEDURE

Type of

Glass

Plate Tempered, Laminated, Wired

Model

Size Max.

Range

Minimum

30x30cm

(12''x12'')

Size Thickness Max.

Range

4.5m

(15ft)

Minimum

30x30cm

(12''x12'')

6.4mm

(1/4'')

(10ft)

RG60

3.2 - 6.4mm

(1/8''-1/4'')

Greater

than

30x30cm

(12''x12'')

(30ft)

Minimum

30x30cm

(12''x12'')

6.4mm

(1/4'')

(20ft)

RG61

Minimum

30x30cm

(12''x12'')

(20ft)

Fig 1: Percentage of Maximum Range as function of angle between Vitron

and glass

Verify that the distance between the VITRON and the furthest point on

the protected glass does not exceed the maximum specified range

taking into account the reduced range due to angle (see Fig 2)

Fig 2:Angle between VITRON and glass

Other factors affecting range:

There should be no obstructions between the VITRON and the protected

glass:

Curtains and blinds may reduce the effective range

Sound absorbing materials in the protected area may reduce the range

ANGLE

VITRON

WINDOW

SIDE VIEW

No adjustments necessary - each unit fully calibrated at factory

Will not alarm if glass pane broken from inside or glass dropped on floor.

Active and passive microphone supervision - verifies unit is working

Full remote test using RG-65 Glass Break Simulator - no need to open

unit

RA66 optional ceiling/wall mount bracket available for optimal mounting

and performance.

Ceiling Mounted

(for optimal results

VITRON is centered

and directed towards

protected glass using

RA-66 Bracket).

Opposite Wall -

Mounted

(For optimal results

VITRON is centered

opposite glass)

Side wall - mounted

(not recommended as

VITRON is not opposite

glass - see range versus

angle diagram.

Test carefully at both

ends of glass using RG-

65 Tester)

For optimal results the VITRON should be mounted as nearly opposite

the glass area to be protected, as shown in Fig 3 below:

STEP 2 MOUNTING LOCATION

Fig 3: VITRON Mounting Options

Open the cover using a flat screwdriver.

STEP 3 MOUNTING

Open the required mounting and cable holes (see Fig 4). The PCB does not

need to be removed unless corner mounting or optional mounting bracket

(RA66) are used.

Fig 4: VITRON Mounting and Cable Holes

Insert the cable through the cable hole and mount the rear cover in its final

location. Seal the remaining holes with sealant.

Snap back the PCB (if removed).

Corner Mounted

(choose corner

opposite glass

to be protected).

VITRON VITRON

VITRON

VITRON VITRON

VITRON

Notes: a) Do not mount VITRON on same wall as protected glass

b) Avoid installing the VITRON near sources of loud noises

or vibrations (air conditioners, fans, compressors, stereos, etc)

75˚

60˚

45˚

30˚

15˚

0˚

VITRON

Mounting

Hole

Holding

Tab

Terminal

Block

Microphone

Alarme

Relay

Holding

Tab

Test

Bouton

Memory Jumper

Screw Hole

Tamper Switch

Terminal

Block

Mounting

Hole

Summary of Contents

Page 1 - INSTALLATION PROCEDURE

SPECIFICATIONSELECTRICALCURRENT CONSUMPTIONVOLTAGE REQUIREMENTSALARM CONTACTSTAMPER CONTACTSACOUSTIC SENSORPHYSICALSIZEWEIGHTGLASSTYPESSIZES87 x 50.7

Directed Electronics 50.7X Specifications

Browse online or download Specifications for Car alarm Directed Electronics 50.7X. Directed Electronics 50.7X Specifications User Manual

Summary of Contents

More documents for Car alarm Directed Electronics 50.7X

Comments to this Manuals

Directed Electronics 50.7X Specifications

Browse online or download Specifications for Car alarm Directed Electronics 50.7X. Directed Electronics 50.7X Specifications User Manual

Summary of Contents

More documents for Car alarm Directed Electronics 50.7X

Comments to this Manuals

Related products and manuals for Car alarm Directed Electronics 50.7X