Directed-electronics S660 User Manual

NOTE: This product is intended for installation by a professional installer only!Any attempt to install this product by any person other than a traine

1100The (+) parking light wire is often found near the switch. Many cars have the switch built into the turn signallever, and in these cars the parkin

1111TThhee bbeesstt ppllaacceess ttoo ffiinndd tthhee ddoooorr sswwiittcchh wwiirree aarree:: At the pin switch: When testing at the pin swi

1122mmaakkiinngg yyoouurr wwiirriinngg ccoonnnneeccttiioonnssBefore making your connections, plan how your wires will be routed through the vehicle

1133pprriimmaarryy hhaarrnneessss ((HH11)),, 1122--ppiinn ccoonnnneeccttoorr______________________________________________________________________

1144ddoooorr lloocckk hhaarrnneessss,, 33--ppiinn ccoonnnneeccttoorr__________________rriibbbboonn hhaarrnneessss,, wwiirriinngg ddiiaaggrraamm

1155pprriimmaarryy hhaarrnneessss ((HH11)) wwiirree ccoonnnneeccttiioonn gguuiiddeeThis wire supplies a (-) ground as long as the system is armed

1166As shipped, this wire should be connected to the (+) parking light wire. If the light flash polarity jumper underthe sliding door is moved to the

1177Connect this wire to the optional domelight supervision relay as shown below:IIMMPPOORRTTAANNTT!! This output is only intended to drive a relay.

1188This wire is used in vehicles that have a positive (+) switched dome light circuit. Connect the violet wire to awire that shows (+)12V when any do

1199Before connecting this wire, remove the supplied fuse. Connect to the battery positive terminal or the constant12V supply to the ignition switch.N

22

2200sseeccoonnddaarryy hhaarrnneessss ((HH22)) wwiirree ccoonnnneeccttiioonn gguuiiddeeThis wire sends a negative pulse every time the remote sta

2211Connect this wire to the wire in the vehicle that sends the signal to turn on the WAIT-TO-START bulb in the dash-board. In most diesels the wire i

2222pplluugg--iinn LLEEDD aanndd vvaalleett//pprrooggrraamm sswwiittcchhThese plug into the module. The Status LED plugs into the small two-pin so

2233sshhoocckk sseennssoorr hhaarrnneessss,, 44--ppiinn ccoonnnneeccttoorrInputs shorter than 0.8 seconds will trigger the Warn Away® response, wh

2244pprrooggrraammmmiinngg jjuummppeerrssThis jumper is used to determine the light flash output. In the (+) position, the on-board relay is enabled

2255The Valet/Program switch, plugged into the blue port, is used for programming. There is a basic sequence ofsteps to remember whenever programming

2266program Channel 2. Release the Valet/Program switch. Press it one time and release it to advance from Channel1 to Channel 2. Now, press and HHOOLL

2277and ...operate...Channel 5operates Remote extended functions/LCD backlightand operates Battery Saver

2288mmuullttii--lleevveell sseeccuurriittyy aarrmmiinnggMulti-Level Security Arming is a feature that allows the user to select which of the system&

2299TToo pprrooggrraamm tthhee ffeeaattuurreess uussiinngg tthhee VVaalleett sswwiittcchh::1.OOppeenn aa ddoooorr.. (The GREEN wire, H1/5, o

33ttaabbllee ooff ccoonntteennttsswwaarrnniinngg!! ssaaffeettyy ffiirrsstt .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..

3300The learn routine will be exited if: The door is closed. The ignition is turned on. The Valet/Program switch is pressed too many times. More t

3311ffeeaattuurree ddeessccrriippttiioonnssThe features of the system are described below. Features that have additional settings that can be selecte

332211--44 IIGGNNIITTIIOONN CCOONNTTRROOLLLLEEDD UUNNLLOOCCKK::When turned ON the doors will unlock when the ignition is turned OFF.11--55 AACCTTI

333322--11 SSIIRREENN OOUUTTPPUUTT CCOONNSSTTAANNTT//PPUULLSSEEDD::The system can be programmed to output pulses instead of a continuousoutput when

334422--77 IIGGNNIITTIIOONN CCOONNTTRROOLLLLEEDD DDOOMMEE LLIIGGHHTT SSUUPPEERRVVIISSIIOONN OONN//OOFFFF::If turned on, the system will turn on

3355nnuuiissaannccee pprreevveennttiioonn cciirrccuuiittrryy™™NPC™ requires that you change the way you test the system as NPC™ will bypass an input

3366ttaabbllee ooff zzoonneessWhen using the Diagnostic functions, use the Table of Zones to see which input has triggered the system. It isalso hel

3377ttrroouubblleesshhoooottiinngg SShhoocckk sseennssoorr ddooeessnn''tt ttrriiggggeerr tthhee aallaarrmm::Has the NPC™ system been tr

3388wwiirriinngg qquuiicckk rreeffeerreennccee gguuiiddeeORANGE ground when armed outputWHITE (+/-) parking light outputWHITE/BLUE No functionLIGHT

3399

44wwaarrnniinngg!! ssaaffeettyy ffiirrssttThe following safety warnings must be observed at all times: Due to the complexity of this system, instal

Get StartedGet ProtectedUngo Pro Security661 W. Redondo Beach Blvd.Gardena, Ca. 90247800-GO-CLARION© 2005 Directed Electronics, Inc. - All rights rese

55ddeecciiddiinngg oonn ccoommppoonneenntt llooccaattiioonnssSSoommee tthhiinnggss ttoo rreemmeemmbbeerr aabboouutt mmoouunnttiinngg tthhee

66 The higher the control module is in the vehicle, the better the transmitter range will be. If you put thecontrol module under a seat or inside a m

77IIMMPPOORRTTAANNTT!! When the vehicle is delivered, please show the user where this switch is locatedand how to disarm the system with it.

88If optional starter kill relay or its connections are immediately visible upon removal of the under-dash panel,they can easily be bypassed. Always m

99The ignition wire is powered when the key is in the run or start position. This is because the ignition wire powersthe ignition system (spark plugs,