© 2000 Directed Electronics, Inc. Vista, CA N417A 9-00®Model 417Installation Guide®Downloaded from: http://www.guardianalarms.net
10 © 2000 Directed Electronics, Inc. Vista, CAmaking your connectionsWhen connecting the security system’s wires to the vehicle wires it is important
© 2000 Directed Electronics, Inc. Vista, CA 111. Using your wire strippers and razor knife, strip approximately 1/2-inch of insulation off the wire to
12 © 2000 Directed Electronics, Inc. Vista, CAprimary harness (H1) wire connection guideThis section of the installation guide describes in detail the
© 2000 Directed Electronics, Inc. Vista, CA 13IMPORTANT! Never interrupt any wire other than the starter wire.NOTE: If connecting the H1/1 wire to con
14 © 2000 Directed Electronics, Inc. Vista, CAH1/3 WHITE/BLUE (+) TRUNK RELEASE, SENSOR SHUNT INPUTThis input is used to bypass sensor inputs when the
© 2000 Directed Electronics, Inc. Vista, CA 15H1/6 BLUE (-) INSTANT TRIGGER, ZONE 1This input will respond to a negative input with an instant trigger
16 © 2000 Directed Electronics, Inc. Vista, CAH1/10 BROWN (+) SIREN OUTPUTConnect this wire to the red wire of the siren. Connect the black wire of th
© 2000 Directed Electronics, Inc. Vista, CA 17plug-in harnessesThe LED operates at 2V DC. Make sure the LED wires are not shorted to ground because th
18 © 2000 Directed Electronics, Inc. Vista, CAoperation mode settingsARMING AND DISARMING WITH THE OEM TRANSMITTERWhen connected to the vehicle’s data
© 2000 Directed Electronics, Inc. Vista, CA 19NOTE: Factory content theft deterrent (CTD) systems in Bonnevilles, Auroras and LeSabres do notmonitor t
2 © 2000 Directed Electronics, Inc. Vista, CAWhat Is Included . . . . . . . . . . . . . . . . . . . . . 3Product Description . . . . . . . . . . . . .
20 © 2000 Directed Electronics, Inc. Vista, CAinternal programming jumpers To access the jumper, open the control module. This jumper is used to deter
© 2000 Directed Electronics, Inc. Vista, CA 21LEVEL II SECURITY MODEWhen this jumper is moved to the Level II position, the databus interface module w
22 © 2000 Directed Electronics, Inc. Vista, CAsystem features learn routineThe System Features Learn Routine dictates how the unit operates. It is pos
© 2000 Directed Electronics, Inc. Vista, CA 235. Release the Valet/program switch.ONCE THE FEATURE IS PROGRAMMED Other features can be programmed. T
24 © 2000 Directed Electronics, Inc. Vista, CA4 DOOR TRIGGER INSTANT/DELAYED: In the instant (default) setting, if a door is opened while the security
© 2000 Directed Electronics, Inc. Vista, CA 25table of zonesWhen using the diagnostic functions, use the Table of Zones to determine which input has t
26 © 2000 Directed Electronics, Inc. Vista, CA Closing the door triggers the system, but opening the door does not: Have you correctly identified the
© 2000 Directed Electronics, Inc. Vista, CA 27
© 2000 Directed Electronics, Inc. Vista, CA 3what is included The control module (see diagram) A Revenger®Soft Chirp®siren The plug-in Valet®/progr
4 © 2000 Directed Electronics, Inc. Vista, CAproduct descriptionThis unit is used to enhance a vehicle’s original equipment from manufacturer (OEM) fa
© 2000 Directed Electronics, Inc. Vista, CA 5AFTER THE INSTALLATION Test all functions. The “Using Your System” section of the Owner’s Guide is very
6 © 2000 Directed Electronics, Inc. Vista, CA Point the siren down so water does not collect in it. Never put the control module in the engine compa
© 2000 Directed Electronics, Inc. Vista, CA 7This system has Remote Valet, so the user can enter and exit Valet Mode without having to reach theValet/
8 © 2000 Directed Electronics, Inc. Vista, CAIf the Failsafe®Starter Kill Relay or its connections are immediately visible upon removal of the underda
© 2000 Directed Electronics, Inc. Vista, CA 9How to find (+)12V ignition with your multimeter:1. Set to DCV or DC voltage (12V or 20V is fine).2. Atta
Comments to this Manuals